DynaClad® PVDF Paint Finish Standard Cool Color Guide (View in PDF Format)
Colors shown may differ depending on monitor, platform, and other factors and thus may vary slightly from actual material.
Custom colors are available
Product Specification (View in PDF Format)
DynaClad, Prefinished Architectural Sheet Metal, Tension Leveled, Coil and Flat Sheet Coated with a 70% Full Strength PVDF Finish System.
Coated on the top side with a polyester primer and a 70% full strength PVDF top coat for a total mil thickness of 1.1 (±.1) The reverse side is a polyester primer and a polyester topcoat with a total dry film thickness of .55 (±.1)
24 ga. or 22 ga. Galvalume DynaClad®
Consists of aluminum-zinc alloy coated (55% aluminum, 43.4% zinc, 1.6% silicon, nominal percentage by weight) carbon steel of commercial weight meeting ASTM 792.
Consists of hot-dipped galvanized steel base sheet of commercial weight (AISI G90 designation) meeting ASTM A653.
.032, .040, .050, .063 Aluminum DynaClad®
Consists of 3105 H14 alloy aluminum base sheet of commercial weight meeting ASTM B209.
Standard stocked Galvalume, G-90 and Aluminum are produced in a 48" wide coil. Standard sized flat sheets are 48" X 120". Custom sized flat sheets can be produced in various widths and lengths with extended lead times and additional costs.
Is applied to the product to protect the paint finish and must be removed immediately after installation. Product should be stored in cool, shaded or covered areas with one side of the crate elevated to permit moisture run-off.
A 20 year finish warranty covering color fade, chalking, and film integrity as well as a 20 year, 6 month perforation warranty (Galvalume® only) covering base sheet integrity is available at no additional cost.
ABRASION RESISTANCE (ASTM D 968)
Passed 60 Liters.
ACCELERATED WEATHERING (ASTM D 822, G 151, & G 153)
3,000 hours with no chalking, blistering or loss of adhesion.
ACID RESISTANCE (ASTM E 1308)
No visible changes.
ADHESION (ASTM D 3359)
No coating removed.
COLOR CHANGE (ASTM D 2244)
After 2,000 hours color change less than 2 NBS units.
FLAME TEST (ASTM E 84)
Class A / Class 1
FLORIDA EXTERIOR DURABILITY (ASTM E 2244 & D 4214)
Less than 5▲E units color change and chalk rating of less than 8.
FORMABILITY (ASTM D 522 & D 4145)
No adhesion loss on a 1/8 Mandrel and 1T bend.
GLOSS (ASTM D 523)
15% (±5%) on 60 degrees.
HUMIDITY (ASTM D 2247)
1,000 hours Galvalume and G-90 acceptable, no change.
3,000 hours Aluminum acceptable, no change.
IMPACT ADHESION (ASTM D 2794)
No cracking or loss of adhesion.
PENCIL HARDNESS (ASTM D 3363)
SALT SPRAY (ASTM B 117)
No blisters or adhesion loss after 1,000 hours for Galvalume® & G-90.
No blisters or adhesion loss after 3,000 hours for Aluminum.
DynaClad is a registered trademark of Dimensional Metals, Inc.
TRINAR is a registered trademark of Akzo Nobel, Inc.
Kynar 500 is a registered trademark of Arkema.
Hylar 5000 is a registered trademark of Ausimont USA, Inc.
Galvalume is a registered trademark of BIEC International, Inc. and some of its licensed producers.
Acrylume is a registered trademark of USX.
Home | About DMI | Products | Forms | Building Green | Contact DMI | Product Catalog | Find a Representative
Terms and Conditions
Copyright © 1999-2017. Dimensional Metals, Inc. All rights reserved.
Website by Forward Function